Create a recess that nearly traverses the wood
I would like to start with a box-shaped piece of hardwood and make a (probably cylindrical) recess in it that nearly traverses the wood, leaving only a very, very thin, uniform layer of wood on the far side. Like this:
The thickness of the thinnest part should be similar to veneers.
Is this achievable with a forstner bit? If so what type? Any special setup?
An alternative: leaving a thicker floor in the recess then planing from the opposite side.
Aside: the goal is, roughly, to make an electrical switchplate cover that has an area where the wood is thin enough to be translucent, such that LEDs could shine through, similar to the following (but maybe with only a single digit of <1in height).
Thanks
technique
asked 4 hours ago
lcgerkelcgerke
111
New contributor
lcgerke is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
I would like to start with a box-shaped piece of hardwood and make a (probably cylindrical) recess in it that nearly traverses the wood, leaving only a very, very thin, uniform layer of wood on the far side. Like this:
The thickness of the thinnest part should be similar to veneers.
Is this achievable with a forstner bit? If so what type? Any special setup?
An alternative: leaving a thicker floor in the recess then planing from the opposite side.
Aside: the goal is, roughly, to make an electrical switchplate cover that has an area where the wood is thin enough to be translucent, such that LEDs could shine through, similar to the following (but maybe with only a single digit of <1in height).
Thanks
technique
asked 4 hours ago
lcgerkelcgerke
111
New contributor
lcgerke is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
A practical point to note is that regardless of whether you mill this from a single piece as you're asking about or though-drill a block and glue on a piece of veneer (a much less challenging and far faster method to achieve basically the same end) the wood overlaying the hole will be very delicate as-is. I would give serious thought to reinforcing from the rear if you have the internal space, e.g. with a layer of clear resin which won't interfere with light transmission.
– Graphus
1 hour ago
Unrelated to the how-to, have you selected the species you'd like to make this from yet?
– Graphus
1 hour ago
add a comment |
I would like to start with a box-shaped piece of hardwood and make a (probably cylindrical) recess in it that nearly traverses the wood, leaving only a very, very thin, uniform layer of wood on the far side. Like this:
The thickness of the thinnest part should be similar to veneers.
Is this achievable with a forstner bit? If so what type? Any special setup?
An alternative: leaving a thicker floor in the recess then planing from the opposite side.
Aside: the goal is, roughly, to make an electrical switchplate cover that has an area where the wood is thin enough to be translucent, such that LEDs could shine through, similar to the following (but maybe with only a single digit of <1in height).
Thanks
technique
asked 4 hours ago
lcgerkelcgerke
111
New contributor
lcgerke is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
I would like to start with a box-shaped piece of hardwood and make a (probably cylindrical) recess in it that nearly traverses the wood, leaving only a very, very thin, uniform layer of wood on the far side. Like this:
The thickness of the thinnest part should be similar to veneers.
Is this achievable with a forstner bit? If so what type? Any special setup?
An alternative: leaving a thicker floor in the recess then planing from the opposite side.
Aside: the goal is, roughly, to make an electrical switchplate cover that has an area where the wood is thin enough to be translucent, such that LEDs could shine through, similar to the following (but maybe with only a single digit of <1in height).
Thanks
technique
technique
asked 4 hours ago
lcgerkelcgerke
111
New contributor
lcgerke is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 4 hours ago
lcgerkelcgerke
111
New contributor
lcgerke is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 4 hours ago
lcgerkelcgerke
111
New contributor
lcgerke is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 4 hours ago
lcgerkelcgerke
111
asked 4 hours ago
lcgerkelcgerke
111
111
New contributor
lcgerke is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
lcgerke is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
lcgerke is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
A practical point to note is that regardless of whether you mill this from a single piece as you're asking about or though-drill a block and glue on a piece of veneer (a much less challenging and far faster method to achieve basically the same end) the wood overlaying the hole will be very delicate as-is. I would give serious thought to reinforcing from the rear if you have the internal space, e.g. with a layer of clear resin which won't interfere with light transmission.
– Graphus
1 hour ago
Unrelated to the how-to, have you selected the species you'd like to make this from yet?
– Graphus
1 hour ago
add a comment |
A practical point to note is that regardless of whether you mill this from a single piece as you're asking about or though-drill a block and glue on a piece of veneer (a much less challenging and far faster method to achieve basically the same end) the wood overlaying the hole will be very delicate as-is. I would give serious thought to reinforcing from the rear if you have the internal space, e.g. with a layer of clear resin which won't interfere with light transmission.
– Graphus
1 hour ago
Unrelated to the how-to, have you selected the species you'd like to make this from yet?
– Graphus
1 hour ago
A practical point to note is that regardless of whether you mill this from a single piece as you're asking about or though-drill a block and glue on a piece of veneer (a much less challenging and far faster method to achieve basically the same end) the wood overlaying the hole will be very delicate as-is. I would give serious thought to reinforcing from the rear if you have the internal space, e.g. with a layer of clear resin which won't interfere with light transmission.
– Graphus
1 hour ago
A practical point to note is that regardless of whether you mill this from a single piece as you're asking about or though-drill a block and glue on a piece of veneer (a much less challenging and far faster method to achieve basically the same end) the wood overlaying the hole will be very delicate as-is. I would give serious thought to reinforcing from the rear if you have the internal space, e.g. with a layer of clear resin which won't interfere with light transmission.
– Graphus
1 hour ago
Unrelated to the how-to, have you selected the species you'd like to make this from yet?
– Graphus
1 hour ago
Unrelated to the how-to, have you selected the species you'd like to make this from yet?
– Graphus
1 hour ago
add a comment |
1 Answer
1
active
oldest
votes
This was almost certainly done by creating a through hole and then gluing veneer over it.
A forstner bit won't work - the edges and lead point make for a not perfectly flat bottomed hole.
If you don't want to go with option 1, in a home shop I would use a router/router table to get close to the finished depth, then plane away at the front surface to get to finished thickness.
answered 2 hours ago
aaronaaron
2,038312
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "603"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
lcgerke is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fwoodworking.stackexchange.com%2fquestions%2f8195%2fcreate-a-recess-that-nearly-traverses-the-wood%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
This was almost certainly done by creating a through hole and then gluing veneer over it.
A forstner bit won't work - the edges and lead point make for a not perfectly flat bottomed hole.
If you don't want to go with option 1, in a home shop I would use a router/router table to get close to the finished depth, then plane away at the front surface to get to finished thickness.
answered 2 hours ago
aaronaaron
2,038312
add a comment |
This was almost certainly done by creating a through hole and then gluing veneer over it.
A forstner bit won't work - the edges and lead point make for a not perfectly flat bottomed hole.
If you don't want to go with option 1, in a home shop I would use a router/router table to get close to the finished depth, then plane away at the front surface to get to finished thickness.
answered 2 hours ago
aaronaaron
2,038312
add a comment |
This was almost certainly done by creating a through hole and then gluing veneer over it.
A forstner bit won't work - the edges and lead point make for a not perfectly flat bottomed hole.
If you don't want to go with option 1, in a home shop I would use a router/router table to get close to the finished depth, then plane away at the front surface to get to finished thickness.
answered 2 hours ago
aaronaaron
2,038312
This was almost certainly done by creating a through hole and then gluing veneer over it.
A forstner bit won't work - the edges and lead point make for a not perfectly flat bottomed hole.
If you don't want to go with option 1, in a home shop I would use a router/router table to get close to the finished depth, then plane away at the front surface to get to finished thickness.
answered 2 hours ago
aaronaaron
2,038312
answered 2 hours ago
aaronaaron
2,038312
answered 2 hours ago
aaronaaron
2,038312
answered 2 hours ago
aaronaaron
2,038312
2,038312
add a comment |
add a comment |
lcgerke is a new contributor. Be nice, and check out our Code of Conduct.
lcgerke is a new contributor. Be nice, and check out our Code of Conduct.
lcgerke is a new contributor. Be nice, and check out our Code of Conduct.
lcgerke is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Woodworking Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fwoodworking.stackexchange.com%2fquestions%2f8195%2fcreate-a-recess-that-nearly-traverses-the-wood%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
A practical point to note is that regardless of whether you mill this from a single piece as you're asking about or though-drill a block and glue on a piece of veneer (a much less challenging and far faster method to achieve basically the same end) the wood overlaying the hole will be very delicate as-is. I would give serious thought to reinforcing from the rear if you have the internal space, e.g. with a layer of clear resin which won't interfere with light transmission.
– Graphus
1 hour ago
Unrelated to the how-to, have you selected the species you'd like to make this from yet?
– Graphus
1 hour ago