Need some help with wall behind rangetop












3















We're in the middle of a kitchen remodel and we have replaced our old 48" Viking slide-in gas rangetop with a new Miele rangetop. The rangetop came with an "island trim" behind the unit which is only a couple of inches high. The installation instructions say that the range needs to be located 10" from any combustible surface, and if you install it flush against a back wall you need to purchase a 12" high backguard at a cost of around $400. One of the reasons we purchased this unit is because my wife really liked the low profile back trim, and Miele's own brochure shows the rangetop up against a tile wall with just the island trim.



So I called Miele customer support. They told me that a tile backsplash behind the unit would be just fine, that the 10" requirement was to ensure that people didn't put something easily flammable directly behind the rangetop. Still, I was concerned so I cranked up the back burners and ran the unit for ten minutes or so and checked the wall temp behind the rangetop. The drywall behind the unit (the tile is not yet installed) measured around 160F. That said, we'll probably only use the back burners once or twice a year since we have three front burners, so it's not like the wall is going to be subjected to constant heat.



So now I don't know what to do. Should I accept the opinion of the customer support guy? Do I have to bite the bullet and buy the expensive backguard that my wife hates? Is there any way I can add protection to the wall by replacing the drywall underlayment with something else on which I can mount the tile?



Thanks, and sorry for the long post.



Stan










share|improve this question



























    3















    We're in the middle of a kitchen remodel and we have replaced our old 48" Viking slide-in gas rangetop with a new Miele rangetop. The rangetop came with an "island trim" behind the unit which is only a couple of inches high. The installation instructions say that the range needs to be located 10" from any combustible surface, and if you install it flush against a back wall you need to purchase a 12" high backguard at a cost of around $400. One of the reasons we purchased this unit is because my wife really liked the low profile back trim, and Miele's own brochure shows the rangetop up against a tile wall with just the island trim.



    So I called Miele customer support. They told me that a tile backsplash behind the unit would be just fine, that the 10" requirement was to ensure that people didn't put something easily flammable directly behind the rangetop. Still, I was concerned so I cranked up the back burners and ran the unit for ten minutes or so and checked the wall temp behind the rangetop. The drywall behind the unit (the tile is not yet installed) measured around 160F. That said, we'll probably only use the back burners once or twice a year since we have three front burners, so it's not like the wall is going to be subjected to constant heat.



    So now I don't know what to do. Should I accept the opinion of the customer support guy? Do I have to bite the bullet and buy the expensive backguard that my wife hates? Is there any way I can add protection to the wall by replacing the drywall underlayment with something else on which I can mount the tile?



    Thanks, and sorry for the long post.



    Stan










    share|improve this question

























      3












      3








      3








      We're in the middle of a kitchen remodel and we have replaced our old 48" Viking slide-in gas rangetop with a new Miele rangetop. The rangetop came with an "island trim" behind the unit which is only a couple of inches high. The installation instructions say that the range needs to be located 10" from any combustible surface, and if you install it flush against a back wall you need to purchase a 12" high backguard at a cost of around $400. One of the reasons we purchased this unit is because my wife really liked the low profile back trim, and Miele's own brochure shows the rangetop up against a tile wall with just the island trim.



      So I called Miele customer support. They told me that a tile backsplash behind the unit would be just fine, that the 10" requirement was to ensure that people didn't put something easily flammable directly behind the rangetop. Still, I was concerned so I cranked up the back burners and ran the unit for ten minutes or so and checked the wall temp behind the rangetop. The drywall behind the unit (the tile is not yet installed) measured around 160F. That said, we'll probably only use the back burners once or twice a year since we have three front burners, so it's not like the wall is going to be subjected to constant heat.



      So now I don't know what to do. Should I accept the opinion of the customer support guy? Do I have to bite the bullet and buy the expensive backguard that my wife hates? Is there any way I can add protection to the wall by replacing the drywall underlayment with something else on which I can mount the tile?



      Thanks, and sorry for the long post.



      Stan










      share|improve this question














      We're in the middle of a kitchen remodel and we have replaced our old 48" Viking slide-in gas rangetop with a new Miele rangetop. The rangetop came with an "island trim" behind the unit which is only a couple of inches high. The installation instructions say that the range needs to be located 10" from any combustible surface, and if you install it flush against a back wall you need to purchase a 12" high backguard at a cost of around $400. One of the reasons we purchased this unit is because my wife really liked the low profile back trim, and Miele's own brochure shows the rangetop up against a tile wall with just the island trim.



      So I called Miele customer support. They told me that a tile backsplash behind the unit would be just fine, that the 10" requirement was to ensure that people didn't put something easily flammable directly behind the rangetop. Still, I was concerned so I cranked up the back burners and ran the unit for ten minutes or so and checked the wall temp behind the rangetop. The drywall behind the unit (the tile is not yet installed) measured around 160F. That said, we'll probably only use the back burners once or twice a year since we have three front burners, so it's not like the wall is going to be subjected to constant heat.



      So now I don't know what to do. Should I accept the opinion of the customer support guy? Do I have to bite the bullet and buy the expensive backguard that my wife hates? Is there any way I can add protection to the wall by replacing the drywall underlayment with something else on which I can mount the tile?



      Thanks, and sorry for the long post.



      Stan







      drywall range






      share|improve this question













      share|improve this question











      share|improve this question




      share|improve this question










      asked 1 hour ago









      Stan McFarlandStan McFarland

      241




      241






















          3 Answers
          3






          active

          oldest

          votes


















          1














          Drywall is perfectly fine. Tile would be even better, but drywall is normal behind a cooktop and is in fact relatively fire resistant. I would avoid wallpaper - it might be a little more flammable and grease would collect on it. But painted drywall is fine.






          share|improve this answer
























          • The wallpaper advice is good. Drywall is not good behind a stove without a back gauge panel. Grease will embed in the drywall and can catch fire after time. You are right it is not an issue on initial use but over time it could be. The stove he is ordering is almost commercial grade - drywall could catch on fire. No restaurant would be code with drywall behind same oven.

            – DMoore
            12 mins ago



















          1














          If you are installing tile then just wait to use the back burners on high until that is done. Any type of tile should be an adequate fire barrier for a stove top.



          If you have to have something in the interim then I suggest taping up some aluminum foil or if you want to get semi-permanent some fire retardant paint.






          share|improve this answer































            1














            If you are tiling the back wall you could replace the drywall with concrete board or just tile it.



            I went with back painted glass as a backsplash behind my cooktop with silicon to seal it to the drywall. It has a pretty great look and glass is like tile - non combustible. It is pricey though so you might be better off with stone or tile.



            example






            share|improve this answer








            New contributor




            Fresh Codemonger is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
            Check out our Code of Conduct.





















              Your Answer








              StackExchange.ready(function() {
              var channelOptions = {
              tags: "".split(" "),
              id: "73"
              };
              initTagRenderer("".split(" "), "".split(" "), channelOptions);

              StackExchange.using("externalEditor", function() {
              // Have to fire editor after snippets, if snippets enabled
              if (StackExchange.settings.snippets.snippetsEnabled) {
              StackExchange.using("snippets", function() {
              createEditor();
              });
              }
              else {
              createEditor();
              }
              });

              function createEditor() {
              StackExchange.prepareEditor({
              heartbeatType: 'answer',
              autoActivateHeartbeat: false,
              convertImagesToLinks: false,
              noModals: true,
              showLowRepImageUploadWarning: true,
              reputationToPostImages: null,
              bindNavPrevention: true,
              postfix: "",
              imageUploader: {
              brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
              contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
              allowUrls: true
              },
              noCode: true, onDemand: true,
              discardSelector: ".discard-answer"
              ,immediatelyShowMarkdownHelp:true
              });


              }
              });














              draft saved

              draft discarded


















              StackExchange.ready(
              function () {
              StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f160891%2fneed-some-help-with-wall-behind-rangetop%23new-answer', 'question_page');
              }
              );

              Post as a guest















              Required, but never shown

























              3 Answers
              3






              active

              oldest

              votes








              3 Answers
              3






              active

              oldest

              votes









              active

              oldest

              votes






              active

              oldest

              votes









              1














              Drywall is perfectly fine. Tile would be even better, but drywall is normal behind a cooktop and is in fact relatively fire resistant. I would avoid wallpaper - it might be a little more flammable and grease would collect on it. But painted drywall is fine.






              share|improve this answer
























              • The wallpaper advice is good. Drywall is not good behind a stove without a back gauge panel. Grease will embed in the drywall and can catch fire after time. You are right it is not an issue on initial use but over time it could be. The stove he is ordering is almost commercial grade - drywall could catch on fire. No restaurant would be code with drywall behind same oven.

                – DMoore
                12 mins ago
















              1














              Drywall is perfectly fine. Tile would be even better, but drywall is normal behind a cooktop and is in fact relatively fire resistant. I would avoid wallpaper - it might be a little more flammable and grease would collect on it. But painted drywall is fine.






              share|improve this answer
























              • The wallpaper advice is good. Drywall is not good behind a stove without a back gauge panel. Grease will embed in the drywall and can catch fire after time. You are right it is not an issue on initial use but over time it could be. The stove he is ordering is almost commercial grade - drywall could catch on fire. No restaurant would be code with drywall behind same oven.

                – DMoore
                12 mins ago














              1












              1








              1







              Drywall is perfectly fine. Tile would be even better, but drywall is normal behind a cooktop and is in fact relatively fire resistant. I would avoid wallpaper - it might be a little more flammable and grease would collect on it. But painted drywall is fine.






              share|improve this answer













              Drywall is perfectly fine. Tile would be even better, but drywall is normal behind a cooktop and is in fact relatively fire resistant. I would avoid wallpaper - it might be a little more flammable and grease would collect on it. But painted drywall is fine.







              share|improve this answer












              share|improve this answer



              share|improve this answer










              answered 1 hour ago









              manassehkatzmanassehkatz

              9,9621337




              9,9621337













              • The wallpaper advice is good. Drywall is not good behind a stove without a back gauge panel. Grease will embed in the drywall and can catch fire after time. You are right it is not an issue on initial use but over time it could be. The stove he is ordering is almost commercial grade - drywall could catch on fire. No restaurant would be code with drywall behind same oven.

                – DMoore
                12 mins ago



















              • The wallpaper advice is good. Drywall is not good behind a stove without a back gauge panel. Grease will embed in the drywall and can catch fire after time. You are right it is not an issue on initial use but over time it could be. The stove he is ordering is almost commercial grade - drywall could catch on fire. No restaurant would be code with drywall behind same oven.

                – DMoore
                12 mins ago

















              The wallpaper advice is good. Drywall is not good behind a stove without a back gauge panel. Grease will embed in the drywall and can catch fire after time. You are right it is not an issue on initial use but over time it could be. The stove he is ordering is almost commercial grade - drywall could catch on fire. No restaurant would be code with drywall behind same oven.

              – DMoore
              12 mins ago





              The wallpaper advice is good. Drywall is not good behind a stove without a back gauge panel. Grease will embed in the drywall and can catch fire after time. You are right it is not an issue on initial use but over time it could be. The stove he is ordering is almost commercial grade - drywall could catch on fire. No restaurant would be code with drywall behind same oven.

              – DMoore
              12 mins ago













              1














              If you are installing tile then just wait to use the back burners on high until that is done. Any type of tile should be an adequate fire barrier for a stove top.



              If you have to have something in the interim then I suggest taping up some aluminum foil or if you want to get semi-permanent some fire retardant paint.






              share|improve this answer




























                1














                If you are installing tile then just wait to use the back burners on high until that is done. Any type of tile should be an adequate fire barrier for a stove top.



                If you have to have something in the interim then I suggest taping up some aluminum foil or if you want to get semi-permanent some fire retardant paint.






                share|improve this answer


























                  1












                  1








                  1







                  If you are installing tile then just wait to use the back burners on high until that is done. Any type of tile should be an adequate fire barrier for a stove top.



                  If you have to have something in the interim then I suggest taping up some aluminum foil or if you want to get semi-permanent some fire retardant paint.






                  share|improve this answer













                  If you are installing tile then just wait to use the back burners on high until that is done. Any type of tile should be an adequate fire barrier for a stove top.



                  If you have to have something in the interim then I suggest taping up some aluminum foil or if you want to get semi-permanent some fire retardant paint.







                  share|improve this answer












                  share|improve this answer



                  share|improve this answer










                  answered 1 hour ago









                  DMooreDMoore

                  29.1k1352121




                  29.1k1352121























                      1














                      If you are tiling the back wall you could replace the drywall with concrete board or just tile it.



                      I went with back painted glass as a backsplash behind my cooktop with silicon to seal it to the drywall. It has a pretty great look and glass is like tile - non combustible. It is pricey though so you might be better off with stone or tile.



                      example






                      share|improve this answer








                      New contributor




                      Fresh Codemonger is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
                      Check out our Code of Conduct.

























                        1














                        If you are tiling the back wall you could replace the drywall with concrete board or just tile it.



                        I went with back painted glass as a backsplash behind my cooktop with silicon to seal it to the drywall. It has a pretty great look and glass is like tile - non combustible. It is pricey though so you might be better off with stone or tile.



                        example






                        share|improve this answer








                        New contributor




                        Fresh Codemonger is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
                        Check out our Code of Conduct.























                          1












                          1








                          1







                          If you are tiling the back wall you could replace the drywall with concrete board or just tile it.



                          I went with back painted glass as a backsplash behind my cooktop with silicon to seal it to the drywall. It has a pretty great look and glass is like tile - non combustible. It is pricey though so you might be better off with stone or tile.



                          example






                          share|improve this answer








                          New contributor




                          Fresh Codemonger is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
                          Check out our Code of Conduct.










                          If you are tiling the back wall you could replace the drywall with concrete board or just tile it.



                          I went with back painted glass as a backsplash behind my cooktop with silicon to seal it to the drywall. It has a pretty great look and glass is like tile - non combustible. It is pricey though so you might be better off with stone or tile.



                          example







                          share|improve this answer








                          New contributor




                          Fresh Codemonger is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
                          Check out our Code of Conduct.









                          share|improve this answer



                          share|improve this answer






                          New contributor




                          Fresh Codemonger is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
                          Check out our Code of Conduct.









                          answered 55 mins ago









                          Fresh CodemongerFresh Codemonger

                          665




                          665




                          New contributor




                          Fresh Codemonger is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
                          Check out our Code of Conduct.





                          New contributor





                          Fresh Codemonger is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
                          Check out our Code of Conduct.






                          Fresh Codemonger is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
                          Check out our Code of Conduct.






























                              draft saved

                              draft discarded




















































                              Thanks for contributing an answer to Home Improvement Stack Exchange!


                              • Please be sure to answer the question. Provide details and share your research!

                              But avoid



                              • Asking for help, clarification, or responding to other answers.

                              • Making statements based on opinion; back them up with references or personal experience.


                              To learn more, see our tips on writing great answers.




                              draft saved


                              draft discarded














                              StackExchange.ready(
                              function () {
                              StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f160891%2fneed-some-help-with-wall-behind-rangetop%23new-answer', 'question_page');
                              }
                              );

                              Post as a guest















                              Required, but never shown





















































                              Required, but never shown














                              Required, but never shown












                              Required, but never shown







                              Required, but never shown

































                              Required, but never shown














                              Required, but never shown












                              Required, but never shown







                              Required, but never shown







                              Popular posts from this blog

                              Knooppunt Holsloot

                              Altaar (religie)

                              Gregoriusmis