Removing debris from PCB












1












$begingroup$


I have a PCB with no solder mask with a very dense layout and a very fine trace spacing.



I didn't get a solder mask because it's still in the prototyping phase, and it's way cheaper.



I keep having to stop, find the new shorts that keep popping up, and remove metal fibers that are barely visible.



From what I can tell the fibers are aluminum from the pcb so a magnet is no help.



Is there a trick to remove them faster or a way to stop this from happening?






pcb-fabrication short-circuit debugging







share|improve this question











$endgroup$








  • 1




    $begingroup$
    Aluminum? That would be rare as aluminum is pretty much only used for the heat sink layer of a metal core pcb. More likely you're learning about Tin whiskers and would benefit from reading more about them. I don't know the answer to this question the way you've phrased it other than "better tools, use solder mask"
    $endgroup$
    – K H
    4 hours ago










  • $begingroup$
    compressed air?
    $endgroup$
    – Wesley Lee
    4 hours ago










  • $begingroup$
    Compressed air didn't help. Your right it is Tin... I looked at "whiskering" on wikipedia, that seems to be whats happening. Tomorrow I'll get some solder on the problem traces and see if that fixes it.
    $endgroup$
    – Tony
    4 hours ago












  • $begingroup$
    Who did the soldering?
    $endgroup$
    – Ale..chenski
    3 hours ago










  • $begingroup$
    Yes, there is one proven way: USE MORE FLUX.
    $endgroup$
    – Ale..chenski
    3 hours ago
















1












$begingroup$


I have a PCB with no solder mask with a very dense layout and a very fine trace spacing.



I didn't get a solder mask because it's still in the prototyping phase, and it's way cheaper.



I keep having to stop, find the new shorts that keep popping up, and remove metal fibers that are barely visible.



From what I can tell the fibers are aluminum from the pcb so a magnet is no help.



Is there a trick to remove them faster or a way to stop this from happening?






pcb-fabrication short-circuit debugging







share|improve this question











$endgroup$








  • 1




    $begingroup$
    Aluminum? That would be rare as aluminum is pretty much only used for the heat sink layer of a metal core pcb. More likely you're learning about Tin whiskers and would benefit from reading more about them. I don't know the answer to this question the way you've phrased it other than "better tools, use solder mask"
    $endgroup$
    – K H
    4 hours ago










  • $begingroup$
    compressed air?
    $endgroup$
    – Wesley Lee
    4 hours ago










  • $begingroup$
    Compressed air didn't help. Your right it is Tin... I looked at "whiskering" on wikipedia, that seems to be whats happening. Tomorrow I'll get some solder on the problem traces and see if that fixes it.
    $endgroup$
    – Tony
    4 hours ago












  • $begingroup$
    Who did the soldering?
    $endgroup$
    – Ale..chenski
    3 hours ago










  • $begingroup$
    Yes, there is one proven way: USE MORE FLUX.
    $endgroup$
    – Ale..chenski
    3 hours ago














1












1








1





$begingroup$


I have a PCB with no solder mask with a very dense layout and a very fine trace spacing.



I didn't get a solder mask because it's still in the prototyping phase, and it's way cheaper.



I keep having to stop, find the new shorts that keep popping up, and remove metal fibers that are barely visible.



From what I can tell the fibers are aluminum from the pcb so a magnet is no help.



Is there a trick to remove them faster or a way to stop this from happening?






pcb-fabrication short-circuit debugging







share|improve this question











$endgroup$




I have a PCB with no solder mask with a very dense layout and a very fine trace spacing.



I didn't get a solder mask because it's still in the prototyping phase, and it's way cheaper.



I keep having to stop, find the new shorts that keep popping up, and remove metal fibers that are barely visible.



From what I can tell the fibers are aluminum from the pcb so a magnet is no help.



Is there a trick to remove them faster or a way to stop this from happening?






pcb-fabrication short-circuit debugging




pcb-fabrication short-circuit debugging






share|improve this question















share|improve this question













share|improve this question




share|improve this question








edited 4 hours ago









Michael Karas

44.4k348103




44.4k348103










asked 4 hours ago









TonyTony

30519




30519








  • 1




    $begingroup$
    Aluminum? That would be rare as aluminum is pretty much only used for the heat sink layer of a metal core pcb. More likely you're learning about Tin whiskers and would benefit from reading more about them. I don't know the answer to this question the way you've phrased it other than "better tools, use solder mask"
    $endgroup$
    – K H
    4 hours ago










  • $begingroup$
    compressed air?
    $endgroup$
    – Wesley Lee
    4 hours ago










  • $begingroup$
    Compressed air didn't help. Your right it is Tin... I looked at "whiskering" on wikipedia, that seems to be whats happening. Tomorrow I'll get some solder on the problem traces and see if that fixes it.
    $endgroup$
    – Tony
    4 hours ago












  • $begingroup$
    Who did the soldering?
    $endgroup$
    – Ale..chenski
    3 hours ago










  • $begingroup$
    Yes, there is one proven way: USE MORE FLUX.
    $endgroup$
    – Ale..chenski
    3 hours ago














  • 1




    $begingroup$
    Aluminum? That would be rare as aluminum is pretty much only used for the heat sink layer of a metal core pcb. More likely you're learning about Tin whiskers and would benefit from reading more about them. I don't know the answer to this question the way you've phrased it other than "better tools, use solder mask"
    $endgroup$
    – K H
    4 hours ago










  • $begingroup$
    compressed air?
    $endgroup$
    – Wesley Lee
    4 hours ago










  • $begingroup$
    Compressed air didn't help. Your right it is Tin... I looked at "whiskering" on wikipedia, that seems to be whats happening. Tomorrow I'll get some solder on the problem traces and see if that fixes it.
    $endgroup$
    – Tony
    4 hours ago












  • $begingroup$
    Who did the soldering?
    $endgroup$
    – Ale..chenski
    3 hours ago










  • $begingroup$
    Yes, there is one proven way: USE MORE FLUX.
    $endgroup$
    – Ale..chenski
    3 hours ago








1




1




$begingroup$
Aluminum? That would be rare as aluminum is pretty much only used for the heat sink layer of a metal core pcb. More likely you're learning about Tin whiskers and would benefit from reading more about them. I don't know the answer to this question the way you've phrased it other than "better tools, use solder mask"
$endgroup$
– K H
4 hours ago




$begingroup$
Aluminum? That would be rare as aluminum is pretty much only used for the heat sink layer of a metal core pcb. More likely you're learning about Tin whiskers and would benefit from reading more about them. I don't know the answer to this question the way you've phrased it other than "better tools, use solder mask"
$endgroup$
– K H
4 hours ago












$begingroup$
compressed air?
$endgroup$
– Wesley Lee
4 hours ago




$begingroup$
compressed air?
$endgroup$
– Wesley Lee
4 hours ago












$begingroup$
Compressed air didn't help. Your right it is Tin... I looked at "whiskering" on wikipedia, that seems to be whats happening. Tomorrow I'll get some solder on the problem traces and see if that fixes it.
$endgroup$
– Tony
4 hours ago






$begingroup$
Compressed air didn't help. Your right it is Tin... I looked at "whiskering" on wikipedia, that seems to be whats happening. Tomorrow I'll get some solder on the problem traces and see if that fixes it.
$endgroup$
– Tony
4 hours ago














$begingroup$
Who did the soldering?
$endgroup$
– Ale..chenski
3 hours ago




$begingroup$
Who did the soldering?
$endgroup$
– Ale..chenski
3 hours ago












$begingroup$
Yes, there is one proven way: USE MORE FLUX.
$endgroup$
– Ale..chenski
3 hours ago




$begingroup$
Yes, there is one proven way: USE MORE FLUX.
$endgroup$
– Ale..chenski
3 hours ago










1 Answer
1






active

oldest

votes


















3












$begingroup$

The trick to stop this from happening is to order your PCB with solder mask. Do consider the cost of your time when deciding that it is cheaper to order boards without.






share|improve this answer









$endgroup$













  • $begingroup$
    I got this board w/ 1 day turn around time with overnight shipping for $250 vs paying over $2000 and 5 day turn around when including a solder mask for a design that hasn't been proven.
    $endgroup$
    – Tony
    4 hours ago










  • $begingroup$
    You might also want to consider using leaded solder, as lead inhibits the formation of whiskers, if that is your problem. As long as you dispose of it properly, there's nothing wrong with using lead in your prototypes, just try to keep it out of any final products.
    $endgroup$
    – Hearth
    3 hours ago










  • $begingroup$
    Yep, that's all we use. All of our designs are just for internal use.
    $endgroup$
    – Tony
    3 hours ago












  • $begingroup$
    Did you end up using more or less than $1750 worth of your time finding and fixing shorts, though?
    $endgroup$
    – The Photon
    2 hours ago










  • $begingroup$
    And if you add a couple of days looking for the shorts (or if they show up as glitches in the future), that 2000$ price tag falls drastically for 48hr and 72hr fabrication.
    $endgroup$
    – Wesley Lee
    1 hour ago











Your Answer





StackExchange.ifUsing("editor", function () {
return StackExchange.using("mathjaxEditing", function () {
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
});
});
}, "mathjax-editing");

StackExchange.ifUsing("editor", function () {
return StackExchange.using("schematics", function () {
StackExchange.schematics.init();
});
}, "cicuitlab");

StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "135"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);

StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});

function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});


}
});














draft saved

draft discarded


















StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f425459%2fremoving-debris-from-pcb%23new-answer', 'question_page');
}
);

Post as a guest















Required, but never shown

























1 Answer
1






active

oldest

votes








1 Answer
1






active

oldest

votes









active

oldest

votes






active

oldest

votes









3












$begingroup$

The trick to stop this from happening is to order your PCB with solder mask. Do consider the cost of your time when deciding that it is cheaper to order boards without.






share|improve this answer









$endgroup$













  • $begingroup$
    I got this board w/ 1 day turn around time with overnight shipping for $250 vs paying over $2000 and 5 day turn around when including a solder mask for a design that hasn't been proven.
    $endgroup$
    – Tony
    4 hours ago










  • $begingroup$
    You might also want to consider using leaded solder, as lead inhibits the formation of whiskers, if that is your problem. As long as you dispose of it properly, there's nothing wrong with using lead in your prototypes, just try to keep it out of any final products.
    $endgroup$
    – Hearth
    3 hours ago










  • $begingroup$
    Yep, that's all we use. All of our designs are just for internal use.
    $endgroup$
    – Tony
    3 hours ago












  • $begingroup$
    Did you end up using more or less than $1750 worth of your time finding and fixing shorts, though?
    $endgroup$
    – The Photon
    2 hours ago










  • $begingroup$
    And if you add a couple of days looking for the shorts (or if they show up as glitches in the future), that 2000$ price tag falls drastically for 48hr and 72hr fabrication.
    $endgroup$
    – Wesley Lee
    1 hour ago
















3












$begingroup$

The trick to stop this from happening is to order your PCB with solder mask. Do consider the cost of your time when deciding that it is cheaper to order boards without.






share|improve this answer









$endgroup$













  • $begingroup$
    I got this board w/ 1 day turn around time with overnight shipping for $250 vs paying over $2000 and 5 day turn around when including a solder mask for a design that hasn't been proven.
    $endgroup$
    – Tony
    4 hours ago










  • $begingroup$
    You might also want to consider using leaded solder, as lead inhibits the formation of whiskers, if that is your problem. As long as you dispose of it properly, there's nothing wrong with using lead in your prototypes, just try to keep it out of any final products.
    $endgroup$
    – Hearth
    3 hours ago










  • $begingroup$
    Yep, that's all we use. All of our designs are just for internal use.
    $endgroup$
    – Tony
    3 hours ago












  • $begingroup$
    Did you end up using more or less than $1750 worth of your time finding and fixing shorts, though?
    $endgroup$
    – The Photon
    2 hours ago










  • $begingroup$
    And if you add a couple of days looking for the shorts (or if they show up as glitches in the future), that 2000$ price tag falls drastically for 48hr and 72hr fabrication.
    $endgroup$
    – Wesley Lee
    1 hour ago














3












3








3





$begingroup$

The trick to stop this from happening is to order your PCB with solder mask. Do consider the cost of your time when deciding that it is cheaper to order boards without.






share|improve this answer









$endgroup$



The trick to stop this from happening is to order your PCB with solder mask. Do consider the cost of your time when deciding that it is cheaper to order boards without.







share|improve this answer












share|improve this answer



share|improve this answer










answered 4 hours ago









Michael KarasMichael Karas

44.4k348103




44.4k348103












  • $begingroup$
    I got this board w/ 1 day turn around time with overnight shipping for $250 vs paying over $2000 and 5 day turn around when including a solder mask for a design that hasn't been proven.
    $endgroup$
    – Tony
    4 hours ago










  • $begingroup$
    You might also want to consider using leaded solder, as lead inhibits the formation of whiskers, if that is your problem. As long as you dispose of it properly, there's nothing wrong with using lead in your prototypes, just try to keep it out of any final products.
    $endgroup$
    – Hearth
    3 hours ago










  • $begingroup$
    Yep, that's all we use. All of our designs are just for internal use.
    $endgroup$
    – Tony
    3 hours ago












  • $begingroup$
    Did you end up using more or less than $1750 worth of your time finding and fixing shorts, though?
    $endgroup$
    – The Photon
    2 hours ago










  • $begingroup$
    And if you add a couple of days looking for the shorts (or if they show up as glitches in the future), that 2000$ price tag falls drastically for 48hr and 72hr fabrication.
    $endgroup$
    – Wesley Lee
    1 hour ago


















  • $begingroup$
    I got this board w/ 1 day turn around time with overnight shipping for $250 vs paying over $2000 and 5 day turn around when including a solder mask for a design that hasn't been proven.
    $endgroup$
    – Tony
    4 hours ago










  • $begingroup$
    You might also want to consider using leaded solder, as lead inhibits the formation of whiskers, if that is your problem. As long as you dispose of it properly, there's nothing wrong with using lead in your prototypes, just try to keep it out of any final products.
    $endgroup$
    – Hearth
    3 hours ago










  • $begingroup$
    Yep, that's all we use. All of our designs are just for internal use.
    $endgroup$
    – Tony
    3 hours ago












  • $begingroup$
    Did you end up using more or less than $1750 worth of your time finding and fixing shorts, though?
    $endgroup$
    – The Photon
    2 hours ago










  • $begingroup$
    And if you add a couple of days looking for the shorts (or if they show up as glitches in the future), that 2000$ price tag falls drastically for 48hr and 72hr fabrication.
    $endgroup$
    – Wesley Lee
    1 hour ago
















$begingroup$
I got this board w/ 1 day turn around time with overnight shipping for $250 vs paying over $2000 and 5 day turn around when including a solder mask for a design that hasn't been proven.
$endgroup$
– Tony
4 hours ago




$begingroup$
I got this board w/ 1 day turn around time with overnight shipping for $250 vs paying over $2000 and 5 day turn around when including a solder mask for a design that hasn't been proven.
$endgroup$
– Tony
4 hours ago












$begingroup$
You might also want to consider using leaded solder, as lead inhibits the formation of whiskers, if that is your problem. As long as you dispose of it properly, there's nothing wrong with using lead in your prototypes, just try to keep it out of any final products.
$endgroup$
– Hearth
3 hours ago




$begingroup$
You might also want to consider using leaded solder, as lead inhibits the formation of whiskers, if that is your problem. As long as you dispose of it properly, there's nothing wrong with using lead in your prototypes, just try to keep it out of any final products.
$endgroup$
– Hearth
3 hours ago












$begingroup$
Yep, that's all we use. All of our designs are just for internal use.
$endgroup$
– Tony
3 hours ago






$begingroup$
Yep, that's all we use. All of our designs are just for internal use.
$endgroup$
– Tony
3 hours ago














$begingroup$
Did you end up using more or less than $1750 worth of your time finding and fixing shorts, though?
$endgroup$
– The Photon
2 hours ago




$begingroup$
Did you end up using more or less than $1750 worth of your time finding and fixing shorts, though?
$endgroup$
– The Photon
2 hours ago












$begingroup$
And if you add a couple of days looking for the shorts (or if they show up as glitches in the future), that 2000$ price tag falls drastically for 48hr and 72hr fabrication.
$endgroup$
– Wesley Lee
1 hour ago




$begingroup$
And if you add a couple of days looking for the shorts (or if they show up as glitches in the future), that 2000$ price tag falls drastically for 48hr and 72hr fabrication.
$endgroup$
– Wesley Lee
1 hour ago


















draft saved

draft discarded




















































Thanks for contributing an answer to Electrical Engineering Stack Exchange!


  • Please be sure to answer the question. Provide details and share your research!

But avoid …



  • Asking for help, clarification, or responding to other answers.

  • Making statements based on opinion; back them up with references or personal experience.


Use MathJax to format equations. MathJax reference.


To learn more, see our tips on writing great answers.




draft saved


draft discarded














StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f425459%2fremoving-debris-from-pcb%23new-answer', 'question_page');
}
);

Post as a guest















Required, but never shown





















































Required, but never shown














Required, but never shown












Required, but never shown







Required, but never shown

































Required, but never shown














Required, but never shown












Required, but never shown







Required, but never shown







-

Popular posts from this blog

Knooppunt Holsloot

Image
Knooppunt Holsloot Kenmerken Wegen A37 × N34 Type knooppunt klaverblad Portaal     Verkeer & Vervoer Knooppunt Holsloot is een verkeersknooppunt op de kruising van de autosnelweg A37 en de N34 in Drenthe, tussen Emmen en Coevorden. Oorspronkelijk was deze aansluiting een afritconstructie van het type Haarlemmermeeraansluiting, zoals bij Knooppunt Hooipolder. Sinds 2002 is het knooppunt omgebouwd tot een volledig klaverblad. Als noviteit werd hier voor het eerst gebruikgemaakt van dimbare verlichting in plaats van de normale vaste tijden waarop de verlichting aan en uit gaat, wat een grote kostenbesparing opleverde. [1] Dat Holsloot als volwaardig knooppunt is uitgevoerd, waarbij alle verkeersstromen en afbuigingen ononderbroken kunnen doorgaan, is uitzonderlijk. Het betreft hier namelijk een aansluiting tussen een autosnelweg en niet-snelweg. Een vergelijkbare situatie treft men nabij Hoensbroek bij het knooppunt Ten Esschen.     Aa
Read more

Altaar (religie)

Image
Deel van de serie over kerkelijk gerei waaronder paramenten en liturgisch vaatwerk gebruikt in de liturgie Liturgisch vaatwerk Vasa sacra Miskelk · Pateen Kelklepeltje Ciborie · Monstrans Pyxis · Custodiale Vasa non sacra Ampullen · Wijwatervat Olievaatje Wierookvat · Ablutievat Paramenten Amict · Albe · Baarkleed · Cingel Tuniek · Dalmatiek · Fanon Kazuifel · Manipel · Stola Gremiale · Benedictievelum Mijter Koorkledij Rochet · Superplie Koorkap · Cappa magna Kovel Kelkgerei Bursa · Kelkvelum Ciborievelum Kerklinnen Corporale · Kelkdoekje Lavabodoekje · Palla Altaardwaal Kerkinterieur Altaar · Ambo Biechtstoel · Communiebank Doksaal · Doopvont Faldistorium Godslamp · Hoogaltaar Heilig Kruisaltaar Katheder · Preekstoel Sedilia Tabernakel · Volksaltaar Liturgische boeken Altaarmissaal Benedictionale · Brevier Evangeliarium · Evangelistarium Graduale · Kyriale Lectionarium Psalter · Rituaal Sacramentarium · Volksmissaal Overige Flambou
Read more

Gregoriusmis

Image
Een afbeelding van de Gregoriusmis uit een getijdenboek gemaakt in de zuidelijke Nederlanden tussen 1500 en 1525 Gregoriusmis, Meester van het Akense Altaar, ca. 1500-1525. Collectie Museum Catharijneconvent De Gregoriusmis of de Mis van Sint Gregorius is een motief in katholieke kunst, dat het eerst verscheen in de late Middeleeuwen en dat nog steeds werd gebruikt tijdens de contrareformatie. Paus Gregorius I (ca. 540-604) is afgebeeld, de H. Mis opdragend, terwijl Christus als de Man van Smarten verschijnt op het altaar dat voor Sint Gregorius staat. Volgens de legende had St. Gregorius gebeden om een teken voor een betwijfelaar van de transsubstantiatieleer, waarop de lijdende Christus tijdens het opdragen van de Mis verscheen om hem te overtuigen en waarbij zijn bloed in de altaarkelk liep. Vaak zijn ook de passiewerktuigen afgebeeld. Zie de categorie Mass of Saint Gregory van Wikimedia Commons voor mediabestanden over dit onderwerp. This page is onl
Read more